Discounts, Cash Back & Free Shipping Offers!! ×
0

Your cart is empty.

US

General class license question pool with answers

General class license question pool with answers

General class license question pool with answers

In the US, the Federal Communications Commission (FCC) offers three Amateur Radio license levels or license classes; Technician class licenseGeneral class license and Extra class license. Per FCC Rule 97.523 only one question pool may exist for each license examination level. Each question pool must contain at least 10 times the number of questions required for a single examination. The question pools are normally valid for 4 years.

With only three license classes, earning a license has never been easier!

Click “Start Test” below to take a free Ham Radio General Class practice test! : Test

The following is a general pool of questions for technicians.

T0A01 (B)

Which of the following is a safety hazard of a 12-volt storage battery?

  • A. Touching both terminals with the hands can cause electrical shock
  • B. Shorting the terminals can cause burns, fire, or an explosion
  • C. RF emissions from a nearby transmitter can cause the electrolyte to emit poison gas
  • D. All these choices are correct

T0A02 (D)

What health hazard is presented by electrical current flowing through the body?

  • A. It may cause injury by heating tissue
  • B. It may disrupt the electrical functions of cells
  • C. It may cause involuntary muscle contractions
  • D. All these choices are correct

T0A03 (B)

In the United States, what circuit does black wire insulation indicate in a three-wire 120 V cable?

  • A. Neutral
  • B. Hot
  • C. Equipment ground
  • D. Black insulation is never used

T0A04 (B)

What is the purpose of a fuse in an electrical circuit?

  • A. To prevent power supply ripple from damaging a component
  • B. To remove power in case of overload
  • C. To limit current to prevent shocks
  • D. All these choices are correct

T0A05 (C)

Why should a 5-ampere fuse never be replaced with a 20-ampere fuse?

  • A. The larger fuse would be likely to blow because it is rated for higher current
  • B. The power supply ripple would greatly increase
  • C. Excessive current could cause a fire
  • D. All these choices are correct

T0A06 (D)

What is a good way to guard against electrical shock at your station?

  • A. Use three-wire cords and plugs for all AC powered equipment
  • B. Connect all AC powered station equipment to a common safety ground
  • C. Install mechanical interlocks in high-voltage circuits
  • D. All these choices are correct

T0A07 (D)

Where should a lightning arrester be installed in a coaxial feed line?

  • A. At the output connector of a transceiver
  • B. At the antenna feed point
  • C. At the ac power service panel
  • D. On a grounded panel near where feed lines enter the building

T0A08 (A)

Where should a fuse or circuit breaker be installed in a 120V AC power circuit?

  • A. In series with the hot conductor only
  • B. In series with the hot and neutral conductors
  • C. In parallel with the hot conductor only
  • D. In parallel with the hot and neutral conductors

T0A09 (C)

What should be done to all external ground rods or earth connections?

  • A. Waterproof them with silicone caulk or electrical tape
  • B. Keep them as far apart as possible
  • C. Bond them together with heavy wire or conductive strap
  • D. Tune them for resonance on the lowest frequency of operation

T0A10 (A)

What hazard is caused by charging or discharging a battery too quickly?

  • A. Overheating or out-gassing
  • B. Excess output ripple
  • C. Half-wave rectification
  • D. Inverse memory effect

T0A11 (D)

What hazard exists in a power supply immediately after turning it off?

  • A. Circulating currents in the dc filter
  • B. Leakage flux in the power transformer
  • C. Voltage transients from kickback diodes
  • D. Charge stored in filter capacitors

T0A12 (B)

Which of the following precautions should be taken when measuring high voltages with a voltmeter?

  • A. Ensure that the voltmeter has very low impedance
  • B. Ensure that the voltmeter and leads are rated for use at the voltages to be measured
  • C. Ensure that the circuit is grounded through the voltmeter
  • D. Ensure that the voltmeter is set to the correct frequency

 ham raduo license,  General class license question

Leave a comment

0

Select Your Country